Replacement Pull Switch for Light of Ceieling Fan

Download Article

Download Clause

If your cap fan pull chain is broken because it was pulled out of the switch, there's an easy way to fix information technology. Open up the switch in the cap fan and remove the broken piece of chain of mountains before replacing it with a longer one. If your switch is entirely unsmooth, purchase a replacement at a local ironmongery before removing the old cardinal and installing the new switch. Make sure you go the power source off before attractive apart the cap fan to be safe.

1. 1

   Turn the power off at the breaker for refuge. Place your breaker, likely either in the basement, a closet, or even outside the sign. Visible the breaker and turn the magnate off for the board where you'll glucinium working with the cap fan to make sure electrical energy isn't still flowing when you're removing the fan's parts.^[1]

   • If you're non sure which switch is for the room with the ceiling fan, put off the intense power good to be safe and sound.

2. 2

   Take the light bulbs to prevent them from break. Set aweigh a run or step BM if necessary to reach the ceiling fan easily. Unscrew the light bulbs carefully and place them on a towel nearby. If the ceiling devotee has whatever sconces or globes, move out these as well past unscrewing them operating theater using a screwdriver to remove whatever screws.^[2]

   Advertisement

3. 3

   Economic consumption a screwdriver to transfer the screws holding the light fixture in place. The ceiling fan's fixture, OR the main trapping where the wiring is stored, will live held together with a some visible screws. Use a screwdriver to bring down out these screws, loosening the regular to see the wiring and switch.^[3]

   • Set the screws and detachable fixture nibble aside in a safe place to reattach them later.

4. 4

   Unscrew the nut on the side of the fixture that holds the switch. Look on the outside of the mending for a small nut. Unscrew this nut case to remove it completely, lease you admittance the ceiling rooter draw out chain switch. Set the nut aside for safekeeping.^[4]

5. 5

   Pull out the interchange to inspect the chain more tight. Straight off that the switch is disentangled from the fixture, look at IT up close. If the wiring of the shift is broken, replace information technology whole. Leverage the replacement open using a screwdriver to see if the Chain just needs to glucinium replaced with a longer piece, or if it would be best to get a unaccustomed switch all at once.^[5]

   • If the range looks standardised, expend a longer length of strand you already have to muddle it instead of buying another one.
   • If the switch looks broken, visit a local hardware store to grease one's palms a replacement.

   Advertisement

1. 1

   Pop open the switch using a small screwdriver. Purchase open the tabs along the switch using a screwdriver. Once you separate it into its 2 pieces, the things within of it, like the chain and spring, will beryllium visible. With the switch open, remove it from the wiring by pull the wires out from the change over.^[6]

   • Be careful not to lose whatsoever of the pieces when you pop the switch afford.
   • If you don't see the spring and chain, conk the protective plate holding them wrong the alternate.

2. 2

   Remove the broken piece of chain from the chemical mechanism. Remove the contents of the shift, including the broken tack of chain connected to a disc and the spring. All of the contents inside the switch will be coarse, making information technology easy to only take them exterior. Pop the broken chain bump off of the disc using a screwdriver. Discard the broken chain after you've removed information technology.^[7]

3. 3

   Put a yearner piece of chain in the old chain's spot. Just as you removed the short broken chain, pop a longer chain that will reach through the fixture into place in the grey chain's spot. Elasticity the thirster Sir Ernst Boris Chain into the platter where the broken chain was using your fingers.^[8]

4. 4

   Reassemble the switch by putt the chain and springtime back into place. Put out the spring and chain attached to the disc back into the switch. Pull the chain finished the hole in the change so you can pull on it well. If you popped off a overprotective plate that holds everything together, press this back into place besides.^[9]

   • Hold belt down the spring and string mechanism using your finger Beaver State a screwdriver and then IT doesn't nonclassical up while you're attaching the two briny switch pieces together.
   • The 2 switch halves will agitat in reply into each other easily.

5. 5

   Place the switch endorse inside the fastness and reattach the alternate Nut. Put the electric switch back in the wires even as you took IT out. Get sure you place the switch next to the topographic point where you unscrewed the nut from the outside of the fix. Screw the nut in reply into billet to hold the switch.^[10]

   Advertisement

1. 1

   Purchase a replacement switching at your local household improvement store. Either take a picture of your longtime shift so you screw which one to purchase, OR disassemble the old change and bring forward it with you. Look for a "fan light switch" or something labelled similarly.^[11]

   • Ask an employee at the home improvement or hardware store for help if you'atomic number 75 not sure which trade to buy.

2. 2

   Disconnect the wires related to to the old switch. Pull or twisting cancelled the connectors that hold in concert the wires will disconnect them from the old switch. Remove each wire that's attached to the old switch by pull off the connectors, and take the old switch out.^[12]

   • Take a picture of which wires are abutting to the switch ahead disassembling it to reference the picture when putting it back together.

3. 3

   Strip 0.5–0.75 in (1.3–1.9 cm) of insulation off of the wires to tie them. Consumption a wire stripper to strip the insulation off of the ends of the wires attached to the untried switch, cut into the insulation with the stripper before pulling it towards the remainder of the telegram to take it. This wish earmark the electric connection to pass through the wires.^[13]

4. 4

   Twist the wires together and cover them with connectors. Place the old wires that your inexperienced wires will attach to and twist them together tightly victimization a dextrorotatory motion. Many wires are color-coded, making it easy to agree the even out wires together. Cover the mere wire with a twist-along connector, making certainly the whole bare wire is covered.^[14]

   • Refer to the picture you took of the wires the old switch connected to, if necessary.
   • Twist-on connectors are besides called conducting wire balmy and can be found at your local ironware store.

5. 5

   Put the red-hot switch into the winnow living accommodations to reattach the nut on the external. Since you removed the reduced nut on the right of the fixture that holds the switch in situ earlier, it's time to reattach IT. Nurse the switch inside the fixture, and screw the junky dorsum on to the outside of the fixture to hold the replacement in situ.^[15]

   Advertisement

1. 1

   Hold the reparatio over the wiring and be intimate it back into seat. With your switch replaced, place the part of the fixture that you removed back into place along top of the wiring. Hold it steady and use up the screws to screw it back in victimization a screwdriver.^[16]

   • Ask someone to hold the fixture in situ patc you screw the screws back in, if in demand.

2. 2

   Put the lightbulbs back into the fixture if needed. If you removed any globes or sconces that went around the bulbs, reattach these first either aside moving them back on or using a screwdriver to reinstall the screws. Receive the lightbulbs and carefully twist each one back into place in the fixture.^[17]

3. 3

   Turn the power back on through the breaker. Return to the breaker and flip the switch that turns back on the great power. If your circuit breaker isn't labeled, make a point you turned the right force back happening by testing the ignite trade in the ceiling sports fan room.^[18]

4. 4

   Test the pull chain to visualise if it kit and boodle. Flick the power switch in the room if needful to turn of events the sports fan on. Now that your ceiling fan pull chain throw is fully installed, pull on it mildly to see if information technology works. If the lights come on or the fan starts to rotate, it's all fast.^[19]

   • Avoid pulling on the chain using a good deal of force because this is often how it breaks.

   Advertisement

Add New Question

• Question

  If the chain of mountains barely came off in my hand do I experience to steal a new switch operating room can I just put the chain back on?

  

  This happened to me 3 days past. I had to buy a new 3-pep pill cap fan switch as the mountain chain that broke will NOT go back in the switch. You'll need a cosmic gem clip to get the wires in the terminal as per the directions that came with the 1 I bought from Lowe's.

• Interrogate

  How do I know if the fan switch is working?

  

  You will ask a power examiner with a light. Check mark each terminal for power with the switch off and on -- if IT lights up when you turn the switch connected, it is a opportune switch.

• Question

  We want to connect a 3-speed wall switch to supersede the mountain chain-pull switch on our cap sports fan. At about point there was a switch for a light, which was removed. There are 4 black wires at heart the bulwark with wire nuts happening them. The new 3-speed switch has 2 black wires. How can we Tell what we are supposed to connect?

  

  2 of the wires were for the light and 2 for the winnow. You wish motive a voltage quizzer light to look which ones are power, unless 2 surgery 3 of the black wires are wired together, then those would be the powerfulness and the other black wires would comprise for the fan or light.

• Question

  My pull strand is threaded through the threaded stock that holds the light cover on, where is the switch? How do I get to it?

  

  First, turn disconnected the breakers or fuse for this physical phenomenon area. Remove the light cover. Look for screws that hold the light plate in. Keep unrivaled hand below the plate and hold onto it as you unscrew the screws. Hand down the screws to someone, or sink into a pants' air pocket. The unit you are sounding for will be inside the housing.

Ask a Question

200 characters left

Include your netmail address to get a message when this question is answered.

Undergo

Advertisement

Things You'll Need

• Ravel
• Screwdriver

• New chain

• Wire stripper
• Substitute swop
• Twist-on connectors

Thanks for submitting a tip for review!

• Disconnect the electricity by turning off the power before treatment the ceiling fan.

Advertisement

About This Article

Article Summary X

To replace a ceiling fan pull switch, you'll require to remove the old switch, detach the wires, and attach a new switch directly to the terminals. To start, turn off the tour breaker that leads to your fan, so you don't risk electrocuting yourself. Past, move out the cover on the fan and unscrew the nut on the away of the pull electrical switch, so you can pull IT come out. Make a point you write down the colors of each wire and which terminals they connect to, since you'll need this data late. Once you've removed the pull swop, take information technology to a home improvement store, and purchase a new one. The new switch should embody identical in size, routine of speeds, and electric power, alternatively it won't be compatible. When you attach the new switch, refer to your notes so you can link up the colored wires to the appropriate terminals. Erstwhile they're attached, screw the nuts backbone in, replace the fan overlay, and flip the breaker back on. To learn how to attach a new substitution using wire nuts, read along!

Did this sum-up help you?

Thanks to all authors for creating a page that has been read 374,210 times.

Did this article help you?

Replacement Pull Switch for Light of Ceieling Fan

Source: https://www.wikihow.com/Replace-a-Ceiling-Fan-Pull-Chain-Switch